當前位置：希尼爾首頁 > 譯海拾貝
> 譯文欣賞
> 鋼簾線焊機Steel
Cord Welder
鋼簾線焊機Steel Cord Welder
原創文章：青島希尼爾翻譯公司 http://www.googlemapbuilder.com
2014-11-18
（非涉密內容）
安裝調試與使用
Installation, Debugging and Operation
一、產品安裝：打開裝包箱，查看機體是否完整。然后把腳輪、觸摸屏支架、百分表安裝好。
I. Product Package: unpack product case and check the machine for integrity,
and then install caster, touch-screen support and dial indicator.
二、產品標牌標識：
II. Product Label
鋼簾線對焊機
Steel Cord Welder
型 號
Model UN-0.6DC(CK) 標準編號
Standard Ref. No. GB15578-95
電源電壓
Voltage 220V 次級電壓
Secondary Voltage 0-2.0V
焊接功率
Welding Power 0.6KVA 初級電流
Primary Current 2.73A
相 數
Phase 1 焊接直徑
Welding Diameter φ0.5-1.62mm
頂鍛壓力
Upset Pressure 0.5-5.0N 調節級數
Adjustment Step 無級調壓
Stepless Adjustment
正常頻率
Normal Frequency 50 Hz 重 量
Weight 140KG
工廠編號
Factory Code A 生產日期
Production Date 年 月 日
MM DD YY
三：焊接前的調整：
III. Pre-welding Adjustment
1、①、查看焊接夾緊上下鉗口左右相距初始距離。一般定為簾線直徑φ0.6-φ1.65mm需要定為3.0mm距離。②、查看左右電極槽溝在一條直線上。調整初始距離時，左面焊接手柄下側定位螺絲，螺絲孔為弧型狀,從左向右調大距離,相反從右向左調小距離,定距后螺釘鎖死。這時按焊接手柄可見初始距離向左移動，聽見咔喳響聲此時是限位開關發出切斷電源的聲音。
1. ① Check initial distances between two sides of the upper and the lower
jaws of a welding tong. Generally, a 3.0mm distance is rated for cord with a
diameter of φ0.6-φ1.65mm. ② Check whether left and right electrode trenches
are on a straight line. To adjust the initial distance, screw the
positioning screw on lower part of a welding handle on the left from the
left to the right to increase the distance, vise versa. The screw hole is
arc-shaped. After the distance is fixed, lock with a bolt. Then, you will
see the initial distance move towards the left by pressing the welding
handle. It clacks when limit switch shuts off the power.
2、打開上蓋，松馳四個內六方螺絲可見前面左夾持鉗口為夾線固定電極連接下機殼。右夾持鉗口為夾線活動電極連接整個焊接傳動系統。①帶動直線光軸。②限位開關斷路連接桿。③限位開關斷路頂絲M4螺絲前調斷電早，后調斷電晚。④傳動燒頭拉簧、平行滑動半軸推動百分表尾左移，使百分表定位0mm-0.4mm-0.68mm分焊線直徑大小而定移位距離。百分表數值為焊接熔化距離。如需要數值增大調動限位開關斷路連接桿滾花備母松動外備母，左旋里備母同時左旋擠緊。相反里備母右旋外備母右旋鎖緊百分表數值減小，連接桿裝有熔化定位膠套，焊接時緩沖焊件回彈不出現裂痕。
2. Open the cover, loosen four hex screws, and then you will see the left
clamping jaw is a thread tension fixed electrode which is connected with the
lower casing, while the right clamping jaw is a thread tension adjustable
electrode which is connected with the entire welding transmission system. ①
Drive linear optical axis. ② Limit switch circuit-breaking connecting rod. ③
The power is shut off early when the limit switch circuit-breaking set screw
(M4) is adjusted forward, and shut off late when it is adjusted backward. ④
Drive burner spring and parallel sliding shaft to push tail of the dial
indicator move towards left and let it position on 0mm-0.4mm-0.68mm.
Displacement is determined according to diameter of welding wire. Dial
indicator reading indicates welding melting distance. If it is required to
increase the reading, adjust knurled nut of the limit switch
circuit-breaking connecting rod to loosen the external nut, and screw the
internal nut to the left while squeezing it by screwing to the left, vise
versa. The connecting rod is equipped with a melting positioning sleeve,
which can cushion weld rebound when welding, thus preventing crack.
3、平行滑動半軸由兩滾動軸承夾緊平衡運行、不緊不松、靈敏傳動，需調整間隙時上軸承軸是六方偏心軸（如平行滑動半軸調整間隙用10mm死口扳子扳動六方軸，手感不緊不松，為標準間隙）。
3. The parallel sliding shaft is clamped by two rolling bearings and runs in
parallel, neither too loose, nor too tight, driving sensitively. When it is
required to adjust clearance, the upper bearing shaft is a hex eccentric
shaft (if clearance of parallel sliding shaft is adjusted by moving the hex
shaft with a 10mm die wrench, the clearance where you feel neither too loose
nor too tight shall be considered as the standard clearance).
4、右活動電極主臂連接導電銅辮子線。需要固定好U型口朝下不能變型否則影響焊接效果。
4. Main arm of the right adjustable electrode is connected with a conductive
braided copper wire. It is required to fix a U-opening face down and
maintain the shape, or welding effect will be affected.
5、插上電源調整燒頭手柄及拉簧桿松緊。扳動手柄向右方向移動。此時拉簧傳動右夾臂鉗口略見移開為最佳。燒頭手柄底端有開關頂絲，拉開時指示燈亮為通電標志。另一根頂絲保護開關不易撞壞。調整完畢蓋好上蓋。
5. Power on to adjust tightness of a burner handle and a return spring rod.
Move the handle towards the right. Then, it will be better when the return
spring drives the right clamp jaw slightly away. Bottom of the burner handle
is equipped with a switch set screw. When pulled away, the indicator lights,
indicating power-on. Another set screw protects the switch from collision.
Close the upper cover after adjustment.
焊接時在夾持鉗口上放好焊線夾緊。開始拉動燒頭手柄，熔斷焊線。焊機機頭上裝有操作按鈕：焊接手柄、退火按鈕、砂輪按鈕、燒頭手柄。電器控制箱裝有照明放大鏡燈開關、電錘調速鈕、機架腳踏開關、控制箱門鎖。
When welding, put a welding wire on the clamp jaw and clamp it tightly.
Begin to pull the burner handle, and melt the welding wire. Welder head is
equipped with buttons: welding handle, annealing button, grinding button and
burner handle. The electric control cabinet is equipped with lighting
magnifying glass lamp switch, electric hammer speed regulating button, frame
foot switch and cabinet door lock.
文章內容由青島希尼爾翻譯公司翻譯
中英對照 中英雙語翻譯 專業翻譯
14785928